Explore deals

Boat Side Guide



 - CE Smith Trailer Post Guide-On with Unlighted Posts, 40
CE Smith Trailer Post Guide-On with Unlighted Posts, 40"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27620, 40" Post Guide-On with Unlighted Posts. These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Fits trailer frames up to 3" wide x 5-1/4" tall. Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating (less than 1 mm) and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so it's recommended that they be primed and painted.

  • Color: Multi
  • Brand: CE Smith
  • ASIN: B0000AXDLQ
  • UPC: 014445589037
 - CE Smith Trailer Roller Guide-On- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
CE Smith Trailer Roller Guide-On- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27610, Roller Guide-On. These smooth rolling guides assist in centring the boat onto the trailer.  Ideal for retrieving your boat on shallow ramps where the trailer is not far into the water, when you are alone, or have a crosswind or current pushing the boat. Uprights with rollers come fully assembled, ready for installation.  For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.

  • Brand: CE Smith
  • ASIN: B0009TTLRA
  • UPC: 080850464573
 - CE Smith Trailer Bunk Board Guide-On, 2'- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
CE Smith Trailer Bunk Board Guide-On, 2'- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27660, 2' Bunk Board Guide-On. Carpeted bunk boards provide proper center loading even in wind or side current conditions. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.

  • Brand: CE Smith
  • ASIN: B001445EUW
  • UPC: 768296001865
 - CE Smith Trailer 2 1/2
CE Smith Trailer 2 1/2" X 12"-1/2" ID 29560 Side

CE Smith 29560, side guide 2-1/2" x 12" - 1/2" ID W/Bushing sleeve. 12" side guide. Black natural rubber rollers are original equipment on many Trailers. Fits standard brackets and shaft sizes.

  • Brand: CE Smith
  • ASIN: B0038ZY95G
  • UPC: 768296002329
 - CE Smith Trailer Bunk Board Guide-On, 5'- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
CE Smith Trailer Bunk Board Guide-On, 5'- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27600, 5' Bunk Board Guide-On. Carpeted bunk boards provide proper center loading even in wind or side current conditions. Adjustable boat guides can be fine-tuned to work with your boat and your trailer. The pre-galvanized steel support posts mount horizontally on top of or below your trailer's frame rail. Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. The bunk boards then tilt to conform to the boat's hull. Guides will help to center your boat during loading and to hold the boat during transport. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mil and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.

  • Color: default title
  • Brand: CE Smith
  • ASIN: B000KK90P6
  • UPC: 768296001230
 - T-902; Boat Trailer Side Guide Roller Assembly, 1 Each ( Zinc Plated Finish )
T-902; Boat Trailer Side Guide Roller Assembly, 1 Each ( Zinc Plated Finish

Boat trailer Guide-Ons have numerous benefits. From the most important, a fast, easy, safe & correct centering of your boat while launching or loading at a crowded boat landing to even helping you guide your trailer to the correct spot and water depth. SIDE GUIDE ROLLER ASSEMBLY -Mostly assembled for ease of installation, ( You only have to press on 1 ea. push-on-cap ) this allows you to use or change the 2 ea. 2-1/2" long carriage bolts the assembly comes with. Ve-Ve roller bracket with 2" diameter x 9" long Side Guide Roller and End Cap rollers fit a majority of today's boat trailer side roller guide arms or tubes. The overall Roller Assembly is 13-1/2" long and slots in bracket give it 1" of adjustment. Roller Bracket is Gold Zinc plated to give added protection against corrosion. Standard metal finish is Gold Zinc plated ( for fresh water use ) or optional "HOT DIPPED GALVANIZED" ( for salt water use ). Packaged and sold singly. VE-VE Inc. marine products are AMERICAN MADE products, not foreign imitations!

  • Brand: VeVe Inc.
  • ASIN: B071XKS8YP
  • UPC: 816311029025
 - CE Smith Trailer PVC Boxed Post Guide-On, Black, 40
CE Smith Trailer PVC Boxed Post Guide-On, Black, 40"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

These new CE Smith post guide-on allow you to see the location of your trailer when its under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Includes 1-1/2" square, 16 gauge pre-galvanized steel uprights, 18" high and 2" schedule 40 black PVC posts (2-3/8" actual outer diameter). stands 40" above trailer frame with black post caps.

  • Color: Black
  • Brand: CE Smith
  • ASIN: B01D1OTWE6
  • UPC: 768296009656
 - CE Smith Trailer Post Guide-On with LED Lighted Posts, 60
CE Smith Trailer Post Guide-On with LED Lighted Posts, 60"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27760, 60" Post Guide-On with LED Lighted Posts. These Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.

  • Brand: CE Smith
  • ASIN: B001RDVFKS
  • UPC: 751738045381
 - SeaSense Black Rubber Guide On Roller
SeaSense Black Rubber Guide On

These are rollers to mount horizontally on both sides of a gate to help stabilize it from tipping over. They are made of rubberized UV protected hard plastic. Designed to stand up to the rigors of even the most extreme climates and these rollers will last for years and are maintenance free due to the internal sealed ball bearings.

  • Brand: SeaSense
  • ASIN: B0019M5LDO
  • UPC: 737765808298
 - Yates Rubber Molded Side Guide Roller 1/2
Yates Rubber Molded Side Guide Roller 1/2" Bore (9" X 2")

Rubber Black Boat Trailer Rollers Molded Side GuideRollers Rollers are O.E.M. replacements for many trailers Length 9" Diameter 2" Shaft size 12"

  • Brand: YATES RUBBER
  • ASIN: B0000AY8L8
 - CE Smith Trailer 2 1/2
CE Smith Trailer 2 1/2" X 9"-5/8" ID 29565 Side

CE Smith 29565, side guide 2-1/2" x 9" - 5/8" ID W/Bushing sleeve. 9" side guide. Black natural rubber rollers are original equipment on many Trailers. Fits standard brackets and shaft sizes.

  • Brand: CE Smith
  • ASIN: B004Y7FJOW
  • UPC: 768296004699
 - CE Smith Trailer Post Guide-On with l-Beam Mounting Kit, 60
CE Smith Trailer Post Guide-On with l-Beam Mounting Kit, 60"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27648, 60" Post Guide-On with l-Beam Mounting Kit. These Post Guide-Ons allow you to see the location of your trailer when it's under water. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam.  Brackets will fit onto any height and virtually any width I-beam trailer frame. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.

  • Brand: CE Smith
  • ASIN: B00HWV7H6K
  • UPC: 768296008406
 - C.H. Yates Rubber 12243-5 2-1/2
C.H. Yates Rubber 12243-5 2-1/2" x 12" Marine Side Guided Roller with 5/8"

Straight Roller - Black End cap rollers are designed to provide side impact protection for keel rollers, bow stops or boat guide ons. Length: 12" Outside Diameter: 2-1/2" Shaft: 5/8"

  • Brand: C.H. Yates Rubber
  • ASIN: B003CVKXAG
  • UPC: 696728240196
 - CE Smith Trailer Post Guide-On with LED Lighted Posts, 40
CE Smith Trailer Post Guide-On with LED Lighted Posts, 40"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat

CE Smith Trailer, 27740, 40" Post Guide-On with LED Lighted Posts. These Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Fits trailer frames up to 3" wide x 5-1/4" tall. Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted. Sold in pairs.

  • Brand: CE Smith
  • ASIN: B001RE2ELQ
  • UPC: 768296006921
 - T-918-G; 18
T-918-G; 18" Horizontal Single-Post Boat Trailer Bunk Guide-On, 1 Pair ( Galvanized Finish

Boat trailer Guide-Ons have numerous benefits. From the most important, a fast, easy, safe & correct centering of your boat while launching or loading at a crowded boat landing to even helping you guide your trailer to the correct spot and water depth. Boat Trailer Bunk Guide-Ons, T-918; 18" Carpeted Bunks, Single Post model, 1 PAIR (1 ea. shown). This model consist of 18" carpeted bunks mounted on 1-1/2" square steel tube bunk arms formed at 96 degrees (6 degrees out past 90 degrees) that help center and load 14 to 16 foot boats in wind or side current conditions. The inside of bunks extend out to 9-1/2" on 3" wide frames or 10-1/2" on 2" wide frames, from each side of trailer frame and have height adjustment of 19" to 25". Gold Zinc plated finish for added protection against corrosion. Packaged in pairs with all mounting hardware for trailer frames up to 3" W. x 4-1/4" H.. Standard metal finish is Gold Zinc plated ( for fresh water use ) or optional "HOT DIPPED GALVANIZED" ( for salt water use ). Packaged and sold in PAIRS. Fasteners are zinc plated on both models. Optional longer bolts, T-7-8; for frames up to 5-1/4" high or T-8-8; for frames up to 6-1/4" high. VE-VE Inc. marine products are AMERICAN MADE products, not foreign imitations!

  • Brand: VeVe Inc.
  • ASIN: B0736J5S13
  • UPC: 816311023184
 - Tie Down 86106 Roller Side Guide - Pair
Tie Down 86106 Roller Side Guide -

Tie Down's roller angle adjusts to the angle of the hull. Roller adjusts up to 16 inches (8 inches on each side). Made of hot dip galvanized steel. Features one piece adjustable clamp with U-bolt. Fits all channel and tube frames.

  • Brand: Tie Down Engineering
  • ASIN: B001445ET8
  • UPC: 081628861068
 - AMRA-105695BK.1 * Attwood Boat Trailer Guide Protectors 48 Inch - Black
AMRA-105695BK.1 * Attwood Boat Trailer Guide Protectors 48 Inch -

Boat Trailer Guide Protectors Trailer guide protectors will not only help protect your boat but will enhance the looks, too. These closed cell polyurethane foam and nylon covered pads slip over your existing trailer guide poles to protect from scratches and impact. Most sport and ski boats are equipped with guide poles attached to the rear sides of the trailer. These poles function as a guide device for the boat when taking it on and off the trailer. The Boat Trailer Guide Protectors simply slide on and fit tightly on the existing guide poles. The Boat Trailer Guide Protectors are designed to float up with the water height to help guide you on boat ramps with steep angles. Available in 4 sizes and a wide variety of colors! Sold in pairs.

  • Brand: attwood
  • ASIN: B00MLBVOSS
 - C.E. Smith 60
C.E. Smith 60" Post Guide-On w/I-Beam Mounting

60" Post Guide-On w/I-Beam Mounting KitProduct DescriptionThese Post Guide-Ons allow you to see the location of your trailer when it's under water. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. Features:Mounting hardware includedSold in pairsAdjusts out to 19" each side1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts

  • Brand: CE Smith
  • ASIN: B0728GZSGC
 - Fulton Economy Trailer Boat Guide
Fulton Economy Trailer Boat

50-Inch Boat Guide

  • Brand: Fulton
  • ASIN: B0000C6FOM
  • UPC: 088154090030
 - VeVe Inc. T-956-G; 5-1/2 Ft. Boat Trailer Bunk Guide-On, 1 Pair (Galvanized Finish)
VeVe Inc. T-956-G; 5-1/2 Ft. Boat Trailer Bunk Guide-On, 1 Pair (Galvanized

Boat trailer Guide-Ons have numerous benefits. From the most important, a fast, easy, safe & correct centering of your boat while launching or loading at a crowded boat landing to even helping you guide your trailer to the correct spot and water depth. Boat Trailer Bunk Guide-Ons, T-956; 5-1/2' Carpeted Bunks model, 1 PAIR (1 ea. shown). This model consist of one pair of carpeted 5-1/2 ft. (66") bunks that help center and load 14 to 18 foot long boats in winds or side current conditions. Inside of bunks extend out to 13" on 3" wide frames and 14" on 2" wide frames from each side of trailer frame on 1-1/2" Sq. x 14 Ga. (.083) thick steel tube bunk arms that are formed at 96 degrees ( 6 degrees out past 90 degrees ) and give bunk height adjustment up to 19" to 25". ( NOTE #1: T-957; "Spacer Brackets" can be added if bunks cannot be adjusted in close enough to boat ). When the tubes are mounted at the widest point on 5-1/2 Ft. bunks, the maximum width between the clamps is 53". Gold Zinc plated finish for added protection against corrosion. Packaged in pairs with all mounting hardware for trailer frames up to 3" W. x 4-1/4" H. ( NOTE #2: When mounting "Guide-On's" on trailers with steps behind the fender, the 2 outside holes may be drilled through the step next to the frame for the ...

  • Brand: VeVe Inc.
  • ASIN: B071W1TZTS
  • UPC: 816311023566

Get a Great Deal on Boat Side Guide.‎

Looking for more Boat Side Guide similar ideas? Try to explore these searches: Tuffrider Leather Belt, Blackberry Leather Case Pouch, and White Gold Ladybug Charm.


           

Boat trailer Guides

Boat Side Guide

Building Trailer guides to save money.

Tags: boats,trailer,how to build

Installation of the CE Smith Bunk-Style Guide-Ons for Boat Trailers - etrailer.com

Boat Side Guide

http://www.etrailer.com/.html Today we'll be doing a demo of the CE Smith bunk style guide ons for boat trailers, 24 inch long, part number CE27660. The CE Smith bunk style guide ons will help keep your boat centered during the loading process despite wind and waves. The bunks are tilt-able ...

Tags:

Install Boat Trailer Guides to Keep Your Boat Straight When Loading

Boat Side Guide

How to make loading your boat on your trailer so much easier and faster. My boat would rarely be straight on my bunk boat trailer when I pulled it out of the water. These trailer guides fixed it.

Tags: boat,boat trailer,guides,review,xtreme trail gu...

NewDealExplorer.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or one of its affiliates.